Відео

Any chance you could post a wiring diagram and parts list for us newbies

Great video,waiting for parts to get here so I can install on my maverick,have one question,inline fuse for second fuse block?

The drain plugs are plugs, not bolts.

Hello, Are you interested in testing our products? We would like to invite you to test the UTV Rear Window for your Honda Pioneer 1000(if your car year is 2016+

Keep cleaning the aluminum sheves with brake clean, its the best way to clean em, same with your belt 😂😅

Great vid, where did you get your wrap around harness for your Honda?

Thx ❤

Your videos have been very helpful sir 👍🏼

very well done!!

I bought this exact ATV, used. The previous owner did not know what the right lever was for. I cannot find any info on it specifically. One forum said it was a front brake, but I see no cable and there is only an electrical connection and tip point of contact when levered.

Would it be recommended to lubricate the linkage

I get to fix my cousins stuff, he got the 1000 in 2020 and breaks everything. About 20 tie rod ends so far. a few axles, a few ball joints, etc. Well he tells me his havent been working right for a few months, then front axle flew out. I go to assess it, and turns out all 4 wheel bearings went bad, the lose bearings caused the brake issues from floppy rotors, and made the front axle cv fail and fly out. The upper a arm bushings on drivers side are failed, along with all 4 a arm bushings in the rear. LOL at the bearing prices mentioned at the end. They ain't 25 bucks a piece anymore thanks to Build Back Better.

The bearings are sealed so you're not actually greasing the bearing. The grease is just filling the inside of the hub to keep dirt and water away from the bearing. I believe the tool is a 40mm for a 1000 Pioneer. I bought a 44mm off of eBay and it won't fit inside the bearing.

Absolutely amazing video, well done. I dominated this job yesterday because of you.

I just got my 24 krx4 1000 es se and now im going to the dunes

Very well illustrated. XTC offers nothing? Thank you!

Great video, My buddy Goose waiting for you in the Golf Cart for you take him for a ride.

Don't know what you had until it's gone...

Excellent, thank you!

What was in the box?

Part numbers for rod ends? I'm thinking about going the same route I have found part number on inners that will work but no outers yet

If you don’t want to do the mile marker 2wd conversion right away. Does it makes sense to just do the locking hubs install only? What are your thoughts on that?

I have the Kawasaki spare tire rack and a spare tire and the tender springs gave out fast. Was not impressed. I decided to replace all of the springs with Shock Therapy springs and have not been disappointed. They are holding up great. Our KRX is a 2021 and it's been holding up great (except for the stock springs).

Welcome back dude! Happy to see you're back at it.

I am curious why you chose the Kawasaki after having a Pioneer. I last spoke with you when I asked about the pioneer in the dunes. I told you I had Pioneer 1000-3 LE. After I started buying stuff to get my pioneer ready for a dune trip. I sold it and bought a Talon. I am just curious what made you go to the Kwai after the honda.

Good to see you again, my friend!!!

Thank you! Quick and to the point

Feb 02 2024.. I just picked up 2024 Kawa krx 4 1000 se I live in SW Mi. I seen ur video on nose reduction on the panel top above filter. I'm was wondering if you or anyone has tried behind seats in my case would be back seats between motor & seat.. l haven't even 20mi on my unit, picked it up 30 Dec 23 As our Temps warmed to 20° I installed windshield with snow on rds I was able to get it out of garage. I had put 2 drinks in cup holders. One just Gatorade the other a Yetti. I was surprised how much Gatorade warmed up. I could feel warm air coming up thru shifting area. It felt like heater was on. Ya the cold made it feel warmer than it was but heat never less. Have you or those you know tried successfully to block heat transfer into cab area.. Tks.. jmh

I have a old school eiger automatic. Have trouble with the the starting . Hard hard to find someone here in central Ohio to work on the Suzuki. Even even the Suzuki shops anything over five years old. That's crazy.

C-Fab all day

Will a wide spool winch fit on that front bumper?

Love your video! Wondering if you're interested in reviewing our sxs or atv accessories? Plz share your contact info we'll send you details.

Manual says don't pry on the clips. Owner prys on the clips. All I saw was the back of your hands.

U talk to much .

Great video. Thank you.

Those clips are the devil, but if you do break them. Napa sells them!

Great job!!! That’s duning. That’s also where we used to race our quads. I have the KRX and was worried how it would perform duning but thanks to your video I know. I’ll get some paddles and leave it stock.

Were you in low gear the whole time?

Hi dose the seat still go all the way back??

How did you run the wires to the back previously? Did you remove all those floor panels when you did that?

Great post, thank you. Needed to flush the coolant as well but little info out there. Fortunately, I found the service manual on line.. 🍻

I done the rcor tenders man what a difference

How has the tuner been the last 3years?

Weird it doesn't have power steering. My 590m 2 seater does.

Do you have the link to the cup holders that you bought?

Did you need to add longer bolts?

Great video thanks!

How do I tighten up the chain on a 1983 KLT 200 ?

What kind of tires are you running?

Nice video. The production quality was excellent.